inteliLIGHT® FRE-220-M-L embedded LoRaWAN™ compatible luminaire controller

- Smart upgrade for luminaire manufacturers.
- Enables individual remote management of streetlight lamps with electronic driver up to 400W (ON/ OFF/ Dimming).
- Specially designed and optimized for LoRaWAN™.
- Autonomous operation based on predefined schedules and digital input (light level sensor and adaptive lighting).
- Adaptive lighting capabilities based on digital input for motion sensing.
- Bandwidth efficient with minimal communication
- Dedicated high-security memory for encryption keys storage.
- Wide range of electrical parameters monitoring: V, W, A, VAR, Wh, VARh and PF.
- Advanced data synchronization and notification mechanism.
- Battery operated RTC, protected against unforeseen communication failure.
- Local infrared interface for local configuration.
- Integrated digital input.
- Over The Air (OTA) firmware update.
- Designed lifetime: 10+ years.
technical details
Lamp Type | LED, CF, HID with electronic driver |
Maximum lamp power | 400W (optional up to 750W) * |
Functions / Operation mode | ON / OFF / Dimming |
Dimming range | 1%-100% (depending on lamp control gear) |
Control interface | Analog 1-10 V / 0-10 V / PWM and reversed PWM / DALI Logarithmic and Linear |
Power supply | 85 – 275VAC / 50Hz-60Hz |
Network interface | LoRaWAN (Class C or Class A) |
RF spectrum | 868MHz / 915MHz / 923MHz |
Inter-node mesh communication | Optionally available, with motion sensor add-on |
Last gasp | Optional |
Firmware update | OTA (over the air) |
GNSS | Optional – Geolocation and precision time (GPS, GLONASS, BeiDou, Galileo and QZSS) |
Security | Encrypted communication based on security keys (AES128-bit) |
Surge protection | max 10kA (IEC 61000-4-5) |
Internal scheduling memory | 128 events (daily / weekdays / weekends / fixed date / exceptions) |
Measurement accuracy | MID grade (±1%) |
Average power consumption | 0.5W |
Maximum power consumption | 2W |
Precision Real Time Clock (RTC) | Yes, battery operated |
Battery operation time | 10 years + |
Real-time lamp operation | Yes |
Digital input | 1x dry contact (for PIR sensor, photocell sensor, open door sensor etc.) |
Tilt sensor | Optional (configurable threshold for tilt & roll) |
Light sensor | Optional – externally connected |
Ingress protection | IP20 (IEC 60529) |
Operating temperature range | -25°C to +70°C |
Operating humidity | 95% non-condensing |
Weight | 125 ± 5 g |
Dimensions (length x width x height) | 110 x 48 x 36 mm |
Mounting | embedded in lamp |
Compliant standards | • RED Directive: LVD Directive & protection of health (EN IEC 62368-1, EN IEC 62479), EMC Directive (ETSI EN 301 489-1, ETSI EN 301 489-3), Efficient use of radio spectrum (ETSI EN 300 220-1, ETSI EN 300 220-2, ETSI EN 303 413) • RoHS Directive • Environmental Testing: EN 60068-2-1, EN 60068-2-2 |
Certifications | CE |
* The controller can be used for luminaires over 750W together with an external contactor, and with limited functionalities (no dimming, no measurements).
measured parameters
- Lamp power
- Line voltage
- Current
- Active power
- Reactive power
- Apparent power
- Power factor
- Energy consumption (active/ reactive)
- Lamp / controller – running hours counter
- Lamp On / Off cycles counter
configurable parameters
- Astronomical calendar scheduler
- Predefined scheduler
- Start state (Input / Schedule / Manual)
- ON/OFF power threshold
- Over/ under voltage threshold
- Over/ under current threshold
- Strike retry count
- Fade time
- Lamp warming time
- Lamp cooldown time
- Data transmission setup
- Alert priority setup
alarms monitored
- Over/ under voltage detection
- Over/ under current detection
- Lamp or ballast fault detection
- Device failure